Results 1 to 9 of 9

Thread: which would be best

  1. #1
    Senior Member mr4x4king's Avatar
    Join Date
    Jul 2012
    Location
    Nesquehoning, Pennsylvania, United States
    Posts
    405
    Post Thanks / Like
    Rep Power
    10

    which would be best

    which would be best

    http://store.rc4wd.com/Rocker-Dig-II...er_p_1321.html

    http://www.punkrc.com/index.php?main...products_id=28

    I think # 2 is but just looking for opinions.



    what about this if I want to use it for a super or Xr10 with 4ws?

    I basically want 4ws to just play around with since I don't think 4ws can be used in completion.

    http://www.punkrc.com/index.php?main...&products_id=2

    let me know
    Thanks
    Last edited by mr4x4king; 02-01-2016 at 05:11 PM.

  2. #2
    Senior Member Winnerone23's Avatar
    Join Date
    Jun 2012
    Location
    williamsport
    Posts
    262
    Post Thanks / Like
    Rep Power
    6
    Punkrc, for sure! Specially over Rc4wd..

    But maybe give HeyOK a look too.. He might have something similar..
    Let's do some Crawlering!
    Team Holmes Hobbies
    Team BmachineRC
    Team Krazed Builds
    Team PURPMART

  3. #3
    Bad Robot Quirk's Avatar
    Join Date
    Apr 2010
    Posts
    1,660
    Post Thanks / Like
    Rep Power
    10
    Punk digs are old school but they worked great.

    FYI: I have one sitting in my electronics box

    Why do I care where Waldo is?

    THE MASTER!!

  4. #4
    Bad Robot Quirk's Avatar
    Join Date
    Apr 2010
    Posts
    1,660
    Post Thanks / Like
    Rep Power
    10
    Punk digs are old school but they worked great.

    FYI: I have one sitting in my electronics box

    Why do I care where Waldo is?

    THE MASTER!!

  5. #5
    Senior Member mr4x4king's Avatar
    Join Date
    Jul 2012
    Location
    Nesquehoning, Pennsylvania, United States
    Posts
    405
    Post Thanks / Like
    Rep Power
    10
    So instead of of old school punk dig the new would be 2esc plugged into a 4ch mt4? Something like that. John you offered that up before but I have not been down that way. Pm me and let me know what you want for it maybe I can send you some cash or parts and have you ship it to me

    Sent from my KYOCERA-C6745 using Tapatalk

  6. #6
    Bad Robot Quirk's Avatar
    Join Date
    Apr 2010
    Posts
    1,660
    Post Thanks / Like
    Rep Power
    10
    Yes 2 esc's and a 4ch radio like a MT4
    You can have the punk dig, PM me your address and I will get it in the mail ASAP.
    Make sure you look at wiring examples so you can hook it up correctly, the ESC input is in the center two lugs/holes and each motor is on the side of them, there are polarity markings, you will need to make sure you are right so the motors turn the same direction. Try to make your motor wires from the punk dig equal front to rear, to help combat clod stall


    Sent from somewhere
    Last edited by Quirk; 02-04-2016 at 12:28 PM.

    Why do I care where Waldo is?

    THE MASTER!!

  7. #7
    Senior Member mr4x4king's Avatar
    Join Date
    Jul 2012
    Location
    Nesquehoning, Pennsylvania, United States
    Posts
    405
    Post Thanks / Like
    Rep Power
    10
    Thank you very much I sent a pm

    Sent from my KYOCERA-C6745 using Tapatalk

  8. #8
    Senior Member mr4x4king's Avatar
    Join Date
    Jul 2012
    Location
    Nesquehoning, Pennsylvania, United States
    Posts
    405
    Post Thanks / Like
    Rep Power
    10
    DigSwitchDiagram.jpg
    1 - Plug the Dig Switch Servo Wire into Receiver's Spare Channel (Usually #3)
    2 - Solder both Wires from the ESC into the Center Pair of Contacts labeled ESC
    3 - Solder both Wires going to Motor #1 (usually Front) to the Outside Contacts labeled Motor #1. Motor #1 may freewheel by de-soldering tab above "DIG" on 2+ Units
    4 - Solder both Wires going to Motor #2 (usually Rear) to the Outside Contacts labeled Motor #2
    5 - Trim TX Channel to Center with normal Endpoints

  9. #9
    Senior Member Winnerone23's Avatar
    Join Date
    Jun 2012
    Location
    williamsport
    Posts
    262
    Post Thanks / Like
    Rep Power
    6
    Ok, how did we end up on Moa, from 4ws... Lol..
    If you have a MT4, 4ws is the simplest and easiest way to go!

    The Lever makes 4ws as simple as turning the steering wheel! Yep, that easy...

    Also, it makes dual esc's that easy too!

    Unfortunately.. For use on a Super.. You can only have one or the other.. :'(

    But I have found, with my Super, that 4ws is more important and stays on the Lever..
    Which makes my dual esc's, basically, a Punk dig.. They are either on or off and are simply on a 3 position switch. (One around the steering wheel)..

    (Side note.. That's awesome John!)
    Let's do some Crawlering!
    Team Holmes Hobbies
    Team BmachineRC
    Team Krazed Builds
    Team PURPMART

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •