Warning: preg_replace(): The /e modifier is deprecated, use preg_replace_callback instead in ..../includes/class_bbcode.php on line 2958

Warning: preg_replace(): The /e modifier is deprecated, use preg_replace_callback instead in ..../includes/class_bbcode.php on line 2958

Warning: preg_replace(): The /e modifier is deprecated, use preg_replace_callback instead in ..../includes/class_bbcode.php on line 2958
Turbo's axial jk rubicon - Page 3
Page 3 of 3 FirstFirst 123
Results 21 to 26 of 26

Thread: Turbo's axial jk rubicon

  1. #21
    Senior Member TURBOFEST's Avatar
    Join Date
    May 2010
    Posts
    108
    Post Thanks / Like
    Rep Power
    8
    Finally..The last piece of my electronics bundle has arrived! These new little WARN winches from RC4WD are pretty awesome looking! I also picked up the winch controller to go along with the new winch so I can have a nice clean install. Keep the awesome "officially licensed" parts coming RC4WD!


    Find this winch here:
    WARN 9.5CTI Winch





    TEAM TCS
    TEAM VP
    TEAM HOLMES HOBBIES
    TEAM WHITE LOTUS
    TEAM RC4WD
    TEAM OTTSIX
    GSRCRC 2008 - 2013 2.2 & SUPER CLASS CHAMP!!
    2012 OVERALL NATIONAL CHAMP!

  2. Likes JSLICK liked this post
  3. #22
    Senior Member TURBOFEST's Avatar
    Join Date
    May 2010
    Posts
    108
    Post Thanks / Like
    Rep Power
    8
    Well, it's been quite awhile since I have updated this thread.


    A few upgrades since the last round consist of:


    FINISHED DRIVELINE
    I snagged some Super Shafty Bomb Proof outputs for the trans. I went with a stubby for the front and a standard for the rear. With the new 6mm outputs that meant also getting some MIP 6mm driveshaft Hub for my MIP driveshafts and some Traxxas screw pins to tie it all together. I also got those from Rick @ Super Shafty! "thumbsup"





    SUPER SHAFTY 6MM OUTPUT HUB FOR MIPS DRIVESHAFTS


    SUPER SHAFTY "STUB" 6MM OUTPUTS FOR AXIAL TRANS


    SUPER SHAFTY "STANDARD" 6MM OUTPUTS FOR AXIAL TRANS


    TRAXXAS SCREW PINS FOR MIP DRIVESHAFTS


    FINISHED WIRING (except lights )


    I put a Holmes Hobbies BRXL and Castle Creations BEC inside an electronics box that fit like a glove on the R2J rock sliders. I went with a 4000mah, 3S NanoTech Lipo. It's long and shallow and fits perfectly between the shock hoops on the SCX10. Mix in a Holmes Hobbies 27t torquemaster and this thing was unstoppable!


    All nice and clean






    Now, it's been awhile since I updated, so, I've driven this thing a lot since some of these mods have been done. I decided to enter this rig in the new Trail Class at the North East National Qualifier thinking it would be fun to try and fend off the Wraiths and 4WS purpose built Trail rigs with my Scaler. Well, not only was the Trail class an absolute blast to drive in, but the little bugger actually pulled out a WIN! I wouldn't have guessed it possible before hand, but now I think this rig will be my full time trail classer! Super fun Class!


    Some pics from the comp. HUGE Thanks to Jake Kolva for the awesome pictures from the event!!!!





    JEEP THE GIANT KILLER!



    Thanks COW RC for the awesome work matt trophies for the NENQ!
    TEAM TCS
    TEAM VP
    TEAM HOLMES HOBBIES
    TEAM WHITE LOTUS
    TEAM RC4WD
    TEAM OTTSIX
    GSRCRC 2008 - 2013 2.2 & SUPER CLASS CHAMP!!
    2012 OVERALL NATIONAL CHAMP!

  4. Thanks JSLICK thanked for this post
    Likes JSLICK liked this post
  5. #23
    Senior Member TURBOFEST's Avatar
    Join Date
    May 2010
    Posts
    108
    Post Thanks / Like
    Rep Power
    8
    Updated
    TEAM TCS
    TEAM VP
    TEAM HOLMES HOBBIES
    TEAM WHITE LOTUS
    TEAM RC4WD
    TEAM OTTSIX
    GSRCRC 2008 - 2013 2.2 & SUPER CLASS CHAMP!!
    2012 OVERALL NATIONAL CHAMP!

  6. #24
    Bad Robot Quirk's Avatar
    Join Date
    Apr 2010
    Posts
    1,660
    Post Thanks / Like
    Rep Power
    10
    Very nice


    ***

    Why do I care where Waldo is?

    THE MASTER!!

  7. #25
    Senior Member TURBOFEST's Avatar
    Join Date
    May 2010
    Posts
    108
    Post Thanks / Like
    Rep Power
    8
    When Vanquish Products released the Q-Series LED lights (Vanquish Products - Rigid Industries - Q series LED Lights), I knew immediately what i wanted to do with them. So, I picked up a pair of Black ones and started brainstorming. I mocked up some simple brackets for the lights, that I will refine after everything is done and running. Here is what i have so far. Rigid Q-Series LED JK Rubicon Headlights
    Worked out PERFECTLY!!!


    Gotta get these and my VP Rigid Light bar wired up so I can get out and blind some wildlife.
    TEAM TCS
    TEAM VP
    TEAM HOLMES HOBBIES
    TEAM WHITE LOTUS
    TEAM RC4WD
    TEAM OTTSIX
    GSRCRC 2008 - 2013 2.2 & SUPER CLASS CHAMP!!
    2012 OVERALL NATIONAL CHAMP!

  8. #26
    Senior Member bmf's Avatar
    Join Date
    Jun 2012
    Location
    Newark, Delaware
    Posts
    123
    Post Thanks / Like
    Rep Power
    6
    the lights are awesome! now i want one of these jks for myself just to do that.
    Wraith RTR ultra 4 style
    Wraith Poision Spyder
    SCX-10 JK rubicon (for the kid)

Page 3 of 3 FirstFirst 123

Similar Threads

  1. OS's Axial/HR 2.2 rig
    By OSRC in forum Axial
    Replies: 6
    Last Post: 11-09-2010, 05:01 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •