Warning: preg_replace(): The /e modifier is deprecated, use preg_replace_callback instead in ..../includes/class_bbcode.php on line 2968
Class 1 Wheel Base
Results 1 to 7 of 7

Thread: Class 1 Wheel Base

  1. #1
    President JSLICK's Avatar
    Join Date
    Apr 2010
    Location
    Stowe, Pa
    Posts
    3,624
    Post Thanks / Like
    Rep Power
    10

    Class 1 Wheel Base

    All Class 1 drivers post up width and length of your rig. Wheel nut to wheel nut.

    Looking through the guideline rules there is nothing about Wheel base but I am curious where we all sit.

    The only one that would help give some direction is the width of the gate, the last guideline.


    Class-1 “Street” Details:
    • Vehicle must have a windshield that fills the entire windshield frame.
    • Full width bumpers are required on the front and rear of the vehicle. Bumpers that are molded into the body qualify. A rear bumper is not required on a flatbed, but adding one to the flatbed will gain the additional scale points. (Bumpers are measured from the outsides and must be the width of your windshield).
    • Wheels must be aligned within the body wheel wells (center of wheels to center of wheel wells +/- 1/2 inch total combined)
    • The vehicles body must be mostly intact. Only mild trimming such as flairs & removing a hardtop are allowed. If the hardtop is removed, a full interior is required (no extreme trimming of bodies allowed *See below.)
    • The tread of the tires cannot extend outside of the wheel wells more then 1/2 of the tread width, flairs can be added to reach min. spec.
    • Vehicle must run a full length rail chassis (The rail chassis must be as long as the vehicles wheelbase) (Tamiya CC-01 chassis are allowed).
    • Truggies are not allowed, flatbeds with full length rail chassis are allowed. The bed must be as wide as the cab the entire length of the bed. Cab only not allowed.
    • Tires can never extend beyond the body’s bumpers or the rear of any truck bed. (Any stingers, fairleads, shackles, bolts, etc are not considered part of a bumper when determining this.)
    • Dovetailing is not allowed.
    • Sectioning or narrowing of the body is not allowed.
    • Bobbing a truck bed is allowed, but must follow all body specs.
    • Boat sides are not allowed.
    • 106mm / 4.19" Max tire size including spares.
    • Gates will be a minimum of 11" wide (so mind your width).
    Last edited by JSLICK; 05-22-2012 at 01:34 PM.
    EPARCCrawlers President

    2010 1.9 Inaugural Champion
    2011 Class 2 Scale Season Champion
    2012 Club Champion 1.9, 2.2, Class 1, Class 2
    2013 Class 2 Scale Season Champion
    2014 East Coast G6 1.9 Driver of the Day


    TEAM DRIVER
    LOCKED UP RC
    - SCALE PERFORMANCE PARTS -

    TEAM DRIVER
    OTTSIX

    TEAM DRIVER
    Purpmart Specialist

    TEAM DRIVER
    CREATIONFAB Web Wheeler


  2. #2
    Administrator brazwewn's Avatar
    Join Date
    Apr 2010
    Location
    Alburtis, PA
    Posts
    3,240
    Post Thanks / Like
    Rep Power
    10
    F350 Sup'r Dooty

    Wheelbase: 8.75"
    Track Width: 7.25"

  3. #3
    Administrator brazwewn's Avatar
    Join Date
    Apr 2010
    Location
    Alburtis, PA
    Posts
    3,240
    Post Thanks / Like
    Rep Power
    10
    Jslick's Nissan

    Wheelbase: 9"
    Track Width: 7"

  4. #4
    President JSLICK's Avatar
    Join Date
    Apr 2010
    Location
    Stowe, Pa
    Posts
    3,624
    Post Thanks / Like
    Rep Power
    10
    D90

    http://store.rc4wd.com/110-Land-Rove...-Kit_p_18.html

    Length: 417mm/16.42inch, Width: 191mm/7.52inch, Height: 166mm/6.54inch

    Wheel base: 282mm/11.10inch
    EPARCCrawlers President

    2010 1.9 Inaugural Champion
    2011 Class 2 Scale Season Champion
    2012 Club Champion 1.9, 2.2, Class 1, Class 2
    2013 Class 2 Scale Season Champion
    2014 East Coast G6 1.9 Driver of the Day


    TEAM DRIVER
    LOCKED UP RC
    - SCALE PERFORMANCE PARTS -

    TEAM DRIVER
    OTTSIX

    TEAM DRIVER
    Purpmart Specialist

    TEAM DRIVER
    CREATIONFAB Web Wheeler


  5. Thanks DIRTY thanked for this post
  6. #5
    Super Moderator SimJunkie's Avatar
    Join Date
    Feb 2012
    Posts
    276
    Post Thanks / Like
    Rep Power
    7
    Headache Hummer:
    L (nut to nut): 9 5/8"
    W (edge to edge): 7 3/8"

    Sim

  7. #6
    Administrator
    Join Date
    Apr 2010
    Location
    Quakertown
    Posts
    319
    Post Thanks / Like
    Rep Power
    10
    Iron datsun

    9" wheelbase
    7" width
    Formerly known as losiredcatcrawler


    1st class one 2011
    2.2 Winner 2010
    3rd 1.9 2010
    Bjv4 Berg 2.2
    Cherokee scx10
    Losi mini Ab design chassis with r/t topper
    Losi mini pro with r/t topper
    Losi micro[/color]

  8. #7
    Senior Member
    Join Date
    Apr 2012
    Location
    Saint Clair, pa
    Posts
    106
    Post Thanks / Like
    Rep Power
    6
    Jero cc-01
    wb: 9.5"
    width: 7.25"

Similar Threads

  1. BDW vertex wheel weights
    By JSLICK in forum Micro Crawlers
    Replies: 4
    Last Post: 01-02-2012, 12:53 PM
  2. 1.9 VP DH Wheel Mod
    By Arct1k in forum Tires and Wheels
    Replies: 0
    Last Post: 12-31-2011, 11:11 PM
  3. Wheel narrowing service
    By Ironman19 in forum General Discussion
    Replies: 0
    Last Post: 06-07-2011, 02:30 AM
  4. RC4WD wheel hub tool
    By Metal Masher in forum Tires and Wheels
    Replies: 2
    Last Post: 11-11-2010, 03:14 AM
  5. Who can get me wheel weights?
    By Tin Soldier in forum General Discussion
    Replies: 9
    Last Post: 05-02-2010, 10:20 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •